Skip to content

Starlink Pivot Mount (Standard 4 / 4 X, Enterprise)

Swivelling mount for slanted, shingled roofs, with installation hardware; fits Standard 4, 4 X and Enterprise.

The Standard Pivot Mount is made for slanted, shingled roofs. Its swivelling mechanism lets the installer fine-tune the angle and direction of the dish. It works with Standard 4, Standard 4 X and Enterprise kits. The box includes the mount, two sealant tape squares, two sealant tape strips, two lag screws and 20 cable routing clips, so the hardware needed for installation is supplied. Starlink recommends a drill, a 6 mm drill bit, a 9/16 in hex socket, a marker and a level. Package size is 280 x 470 x 105 mm and package weight is 1.9 kg.

  • For slanted, shingled roofs
  • Swivel to fine-tune angle and direction
  • Fits Standard 4, Standard 4 X, Enterprise
  • Includes lag screws, sealant tape, 20 clips
  • Package 280 x 470 x 105 mm, 1.9 kg
Starlink Pivot Mount (Standard 4 / 4 X, Enterprise) datasheet (PDF)

Authorised Starlink partner in Jordan · Local warranty and support

More Starlink products in Jordan

Why buy through Vodatel

Local technical support

Factory-trained engineers in Amman handle installation, configuration and maintenance.

Supply and rollout

From single units to multi-site deployments, delivered and commissioned by our team.

Warranty backed

Manufacturer warranty handled locally — no cross-border returns to manage.

More from Satellite Internet

Related products

  • Starlink V5
    Starlink

    Starlink V5

    Starlink V5 is a lightweight home kit with a smaller form factor and greater power efficiency than Standard 4 X. The dish measures 384 x 306 x 34 mm and weighs 1.1 kg (3.8 kg for the full kit), is rated IP67 Type 4 and uses an average of 35-50 W. It comes with a Router Mini (Wi-Fi 6, up to 235…

  • Starlink Wall Mount (Standard 4 / 4 X)
    Starlink

    Starlink Wall Mount (Standard 4 / 4 X)

    The Starlink Wall Mount is installed on an exterior wall near the top of the gable or fascia, giving the dish a platform that reaches out from the wall. It accommodates an overhang of up to 4 in and works with Standard 4, Standard 4 X and Enterprise kits. The box includes the wall mount, silicone,…

  • Starlink Pipe Adapter (Standard 4 / 4 X)
    Starlink

    Starlink Pipe Adapter (Standard 4 / 4 X)

    The Pipe Adapter attaches the Standard dish to an existing metal pole with a diameter of 31-63.5 mm (1.25-2.5 in). The pipe is not included, and the adapter is not for PVC or plastic pipes. It works with Standard 4, Standard 4 X and Enterprise kits. The box contains the Pipe Adapter Mount, an Allen…

  • Starlink Ridgeline Mount (Standard 4 / 4 X)
    Starlink

    Starlink Ridgeline Mount (Standard 4 / 4 X)

    The Ridgeline Mount needs no drilling. It sits on the top ridge of a gable roof and is held in place by ballast weights, and it is rated for winds up to 80 kph (50 mph). It suits metal and shingled roofs with a slope under 45 degrees and is not recommended for clay tile. It works with Standard 4,…

  • Starlink Mobility Mount (Standard 4 / 4 X)
    Starlink

    Starlink Mobility Mount (Standard 4 / 4 X)

    The Mobility Mount is a permanent mount that seals against water ingress on wood, fibreglass, metal, plastic and slotted vehicle rack rails. Its stainless steel fasteners are corrosion resistant, and its 8° mounting angle helps keep a signal in wet weather. It works with Standard 4 and Standard 4 X.…

  • Starlink Roof Rack Mount (Standard 4 / 4 X)
    Starlink

    Starlink Roof Rack Mount (Standard 4 / 4 X)

    The Roof Rack Mount is a removable mount that attaches the Standard dish to vehicle roof racks with a thickness of 15-44.5 mm and a width of up to 95 mm, or to racks with compatible T-slots. It works with Standard 4 and Standard 4 X. The box contains the mount base, a grip pad, four M8 flanged head…

  • Starlink X-Frame Base (Standard 4 / 4 X, Enterprise)
    Starlink

    Starlink X-Frame Base (Standard 4 / 4 X, Enterprise)

    The X-Frame Base is for ground-level installation or quick setup of the Standard dish, where no roof or wall mounting is needed. It is supplied with a mast and a mast adapter. It works with Standard 4, Standard 4 X and Enterprise kits. The box contains the X-Frame Base, the Mast Adapter and the…

  • Starlink Standard 4 / 4 X to Actuated Mount Adapter
    Starlink

    Starlink Standard 4 / 4 X to Actuated Mount Adapter

    This adapter lets a Standard 4 or Standard 4 X dish use an existing Standard Actuated mount (Short Wall, Long Wall, Pivot, Ground Pole or Ridgeline), for customers upgrading from the older kit. The wall mount itself is not included. Starlink recommends a Standard mount for new installations. The box…

Talk to us

Ready to specify Starlink Pivot Mount (Standard 4 / 4 X, Enterprise)?

Send us your requirement and our engineers will confirm compatibility, quantities and lead time — usually the same working day.