Five dry contact inputs through a single RJ-45 sensor port on sensorProbe2 and sensorProbe2+
The AKCP 5 Dry Contact Inputs cable lets a sensorProbe2 or sensorProbe2+ read up to five open/closed contacts through one RJ-45 sensor port. Each input reports Alarm or Normal and can be defined by the user to watch things such as UPS status, security systems or air conditioning status. Alarms can be sent by SNMP trap or email with the fault description and location. It reaches up to 305 m on approved cable and takes its power from the base unit. The inputs are not isolated, so no voltage source should be connected. Vodatel supplies, installs and supports it in Jordan as an authorised AKCP partner.
Authorised AKCP partner in Jordan · Local warranty and support
More AKCP products in JordanFactory-trained engineers in Amman handle installation, configuration and maintenance.
From single units to multi-site deployments, delivered and commissioned by our team.
Manufacturer warranty handled locally — no cross-border returns to manage.
| Measures | Dry contact status (Alarm or Normal) |
|---|---|
| Measurement range | Alarm or Normal |
| Sensor type | Open / closed contact switch (input only) |
| Measurement rate | Multiple readings every second; normal input state is settable in software |
| Sensor count | 5 |
| Compatible base units | sensorProbe2, sensorProbe2+ (per-port licence needed on sensorProbe2+) |
| Dry contacts | 5 per RJ-45 sensor port; up to 10 on sensorProbe2, up to 20 on sensorProbe2+ |
|---|---|
| Inputs | 5 V pulled-up dry contacts, input only; contacts are not isolated (do not connect any voltage source) |
| Notifications | SNMP traps and email with fault description and location |
|---|
| Connection | RJ-45 to the sensor port, UTP Cat 5 cable |
|---|---|
| Maximum cable length | 305 m (1000 ft) with approved low-capacitance shielded cable or UTP |
| Power supply | Powered by the controller unit; no additional power needed |
|---|
| Dimensions | 56 × 55 × 33.3 mm |
|---|---|
| Mounting | DIN rail mounting, screw mounting |
| Licence | Additional per-port licence required to unlock the feature on sensorProbe2+ |
|---|
| Brand | AKCP |
|---|---|
| Category | Data Centre & Environmental Monitoring |
| Product code | akcp-5-dry-contact-inputs |
| Type | Sensor |
| Measures | Dry contact |
| Connectivity | RJ-45 sensor port |
Full electrical, acoustic and interface specifications are published on the manufacturer's datasheet. Our team can confirm compatibility with your existing platform before you order.
The AKCP 4-20mA Converter lets a sensorProbe base unit read third-party transmitters that output a 4–20 mA current loop, a signal widely used in process control because it resists electrical noise over long distances. Typical sources include CO2 sensors, pH meters, air particle sensors and precision…
The AKCP Vibration Sensor is a normally closed contact switch that signals an alarm when vibration strikes the surface it protects, or when a window is broken. It guards walls, ceilings, windows, safes and cabinets against forced entry or tampering, and a built-in tamper switch on a separate circuit…
The AKCP Smoke Detector is a photoelectric detector that turns smoke detection into a network-monitored alarm. It reports Smoke or No Smoke to a sensorProbe+ or securityProbe base unit through an RJ-45 sensor port, and can also connect to a fire alarm panel at the same time. A disconnect alarm…
The AKCP Siren and Strobe Light adds a loud audible alarm and a bright flashing light to sensorProbe+ and securityProbe base units, using a single intelligent sensor port and no extra power supply. The siren reaches 100 dB at 100 cm and the strobe uses eight super bright LEDs flashing 400 times per…
Send us your requirement and our engineers will confirm compatibility, quantities and lead time — usually the same working day.
